
NEXiS CS2G Series ProtonProducts Việt Nam
Price: Contact
Brand: Proton
Category: Testing and Measuring Equipment
Supplier: Jon&Jul Việt Nam
Origin: Japan
Ứng dụng sản phẩm: accessory, Automation equipment, Electronic, Industry, Mechanical
![]() |
Online | 4 |
![]() |
Access times | 612701 |
NEXiS CS2G Series ProtonProducts Việt Nam
Price: Contact
Brand: Proton
Category: Testing and Measuring Equipment
Supplier: Jon&Jul Việt Nam
Origin: Japan
Ứng dụng sản phẩm: accessory, Automation equipment, Electronic, Industry, Mechanical
Proton Products' NEXiS ® CS2G series of controllers are used on insulated wire or other extrusion production lines.
The NEXiS ® CS2G series controller connects to Proton Products' diameter gauges as well as speed and length gauges to measure insulation diameter and line speed, respectively. These measurements are then fed into a PI feedback controller with a floating and fully isolated output that can be used to control an insulation extruder or capct drive.
Proton Products' NEXiS ® CS2G series of controllers are used on insulated wire or other extrusion production lines.
The NEXiS ® CS2G series controller connects to Proton Products' diameter gauges as well as speed and length gauges to measure insulation diameter and line speed, respectively. These measurements are then fed into a PI feedback controller with a floating and fully isolated output that can be used to control an insulation extruder or capct drive.
Therefore, the insulation diameter is actively controlled and kept within tolerances using the NEXiS ® CS2G controller.
The NEXiS ® CS2G is connected to the Cold DG diameter gauge behind the water cooling trough. Cold diameter measurement is used to control the extruder so that the final insulation diameter is kept within tolerance. Because the cold diameter measurement is away from the extruder, the response time of this control system is relatively slow (and depends on the line speed), but shrinkage compensation is not required.
The NEXiS ® CS2G is connected to the Hot DG diameter gauge in front of the water radiator. The cooling shrinkage compensation is set by the operator and used in conjunction with the Hot diameter measurement to control the extruder so that the final insulation diameter is kept within tolerance. Because the hot diameter measurement is located close to the extruder, the response time of this control system is relatively fast.
Variant | Control algorithm |
---|---|
NEXiS TM CS2G-10 | For connection to single axis Proton products (DG1xxx) DG series diameter gauges. |
NEXiS TM CS2G-10XY | For connection to dual axis Proton products (DG2xxx) DG series diameter gauge; Controls the average of X and Y diameters. |
Screen | 2-row, 7-segment, 5-digit display | Upper row seats are 0.8” (20.32mm) high; bottom row 0.5” (12.7mm) high | ||
Serial communication | RS232 | USB | CANbus – (for connection to 1× DG current meter) | |
Line speed input | Similar | Two inputs are available for 0 to 10V and 0 to 50V analog line rate signals; the end user can configure the rate | ||
Pulse | Two inputs are available for 0 to 3V and 0 to 10V pulse line speed signals; Maximum frequency 250 kHz; the end user can configure the rate | |||
4×Relay contact output | Functionality (end user configurable) | Measuring meter | An SSFD neck tumor or defect was detected | |
Exceeded tolerance on X or Y | Exceed lower tolerance X or Y | |||
X exceeds the above tolerance | X lower tolerance has been exceeded | |||
Exceeds the upper tolerance of Y | Exceeds lower tolerance Y | |||
Electricity | Maximum voltage | 50VDC / 30VAC | ||
Maximum current | 500mA | |||
About resistance (@100mA) | <0,1Ω | |||
Turn off resistance | > 10 Ω | |||
Analog output 1 | Functionality (end user configurable) | BULLS | ØXY | |
Electricity | Output voltage range | 0V to +10V | ||
Maximum output current | 2mA | |||
Resolution | 16-bit | |||
The end user can configure the output voltage scale | ||||
Analog output 2 | Functionality (end user configurable) | ISLAND | Average error | |
Electricity | Output voltage range | ØY: 0V to +10V | ||
Average error: -10V to +10V | ||||
Maximum output current | 2mA | |||
Resolution | 16-bit | |||
The end user can configure the output voltage scale | ||||
Control algorithm | Advanced Control Algorithm (ACA) |
Indication | minimum | Featured | Max | Units |
---|---|---|---|---|
Weight | 2,5 | Kg | ||
5,5 | lb | |||
Length | 230 | mm | ||
9.1 | inch | |||
Width | 213.1 | mm | ||
8,4 | inch | |||
Height | 128,5 | mm | ||
5.1 | inch | |||
Supply voltage (rms) | 84 | 264 | VAC | |
Power frequency | 47 | 440 | Hz | |
Supply current (rms) | 1 | ONE | ||
Energy consumption | 35 | IN | ||
Ambient temperature | 5 | 45 | °C | |
41 | 113 | ° F | ||
Relative humidity @ 38°C / 105°F | 90 | % | ||
Ingress Protection (IP) Rating | IP50 | – | ||
PI controller output voltage | -10 | 10 | IN. | |
Output current of PI controller | 10 | and | ||
Output resistance of PI controller | 10 | Oh | ||
Resolution of PI controller | 12 | little |
Link FaceBook Jon&Jul VietNam
![]() |
|
HotLine | |
![]() |
|
![]() |
|
![]() |
𝐉𝐎𝐍 & 𝐉𝐔𝐋 𝐈𝐍𝐕𝐄𝐒𝐓𝐌𝐄𝐍𝐓 𝐃𝐄𝐕𝐄𝐋𝐎𝐏𝐌𝐄𝐍𝐓 𝐂𝐎., 𝐋𝐓𝐃
𝐀𝐝𝐝𝐫𝐞𝐬𝐬 : No. 4, Street 14, Van Phuc Urban Area, Hiep Binh Phuoc W., Thu Duc, Ho Chi Minh City, Vietnam
𝐄𝐦𝐚𝐢𝐥 : sales@jon-jul.com
Hotline: 094 1035500
𝐖𝐞𝐛𝐬𝐢𝐭𝐞: https://jon-jul.com/